Recent Updates
  • Aluminum Lamp Housing Manufacturer Share How To Properly Design Street Lights

    Then the Aluminum Lamp Housing Manufacturer will answer why this happens, it may be that the lights cannot be turned on after dark due to the following reasons.

    Voltage: The controller shows that the battery is under pressure and cannot be illuminated after dark, but the battery voltage has exceeded this point under the pressure value, indicating that the battery has been charged. In the 12v system, the lower voltage protection value is about 11.1v (default value of the controller). After the battery drops to this voltage point, the controller will turn off the power, stop discharging, protect the battery but release it.

    Reason: The solar panel charges the battery during the day and charges the voltage to 12V (the default value of the controller) before continuing to discharge to prevent the battery from being damaged by deep discharge for a long time. Then, after the battery is under voltage, if the controller is not restarted, 11.1 or 12V is under voltage, you must wait for the battery to recharge to 12V before you can continue to discharge.

    Solution: It is sufficient to charge the battery voltage to 12V or higher using a solar panel or DC charger.

    Second, the controller: If the LED street lamp has been installed and can be turned on normally for a period of time, the controller fails. The controller is damaged because the system is subjected to strong electrical shock, such as direct lightning or short circuit, or the internal electronic components of the controller may be damaged.

    Solution: replace the controller, test the controller, and check the response of the indicator light. If neither indicator is lit, the controller will be damaged and must be replaced.

    Three, LED light source DC power drive: the indicator light of the detection controller shows normal discharge, and the battery voltage is sufficient, that is, the light is off. At this time, the anode and cathode of the lamp should be directly connected to the anode and cathode of the battery. If it cannot be discharged, the DC power supply of the LED light source will be damaged. Need to be replaced. The LED light source DC power driver is now integrated with the controller in the aluminum box. Installation and maintenance are simpler and more convenient. If a component is damaged, it can be replaced directly.

    The above content is organized and shared by LED Street Light Housing | Die-cast Aluminum Light Housing manufacturer , hoping to help those in need.

    Aluminum Lamp Housing Manufacturer Share How To Properly Design Street Lights Then the Aluminum Lamp Housing Manufacturer will answer why this happens, it may be that the lights cannot be turned on after dark due to the following reasons. Voltage: The controller shows that the battery is under pressure and cannot be illuminated after dark, but the battery voltage has exceeded this point under the pressure value, indicating that the battery has been charged. In the 12v system, the lower voltage protection value is about 11.1v (default value of the controller). After the battery drops to this voltage point, the controller will turn off the power, stop discharging, protect the battery but release it. Reason: The solar panel charges the battery during the day and charges the voltage to 12V (the default value of the controller) before continuing to discharge to prevent the battery from being damaged by deep discharge for a long time. Then, after the battery is under voltage, if the controller is not restarted, 11.1 or 12V is under voltage, you must wait for the battery to recharge to 12V before you can continue to discharge. Solution: It is sufficient to charge the battery voltage to 12V or higher using a solar panel or DC charger. Second, the controller: If the LED street lamp has been installed and can be turned on normally for a period of time, the controller fails. The controller is damaged because the system is subjected to strong electrical shock, such as direct lightning or short circuit, or the internal electronic components of the controller may be damaged. Solution: replace the controller, test the controller, and check the response of the indicator light. If neither indicator is lit, the controller will be damaged and must be replaced. Three, LED light source DC power drive: the indicator light of the detection controller shows normal discharge, and the battery voltage is sufficient, that is, the light is off. At this time, the anode and cathode of the lamp should be directly connected to the anode and cathode of the battery. If it cannot be discharged, the DC power supply of the LED light source will be damaged. Need to be replaced. The LED light source DC power driver is now integrated with the controller in the aluminum box. Installation and maintenance are simpler and more convenient. If a component is damaged, it can be replaced directly. The above content is organized and shared by LED Street Light Housing | Die-cast Aluminum Light Housing manufacturer , hoping to help those in need.
    0 Comments 0 Shares
  • Aluminum Lamp Housing Manufacturer Introduces The Installation Skills Of Lamps

    Aluminum Lamp Housing Manufacturer introduces the installation requirements of common lamps

    1. The lamps and accessories should be complete, and there should be no defects such as mechanical damage, deformation, peeling paint and cracked lampshades.

    2. The bearing capacity of the fixture on the wall ceiling where the luminaire is installed should match the weight of the luminaire.

    3. The chandelier should be equipped with a wire box, and each wire box can only be equipped with one set of chandelier. The surface of the chandelier must be well insulated, there must be no joints, and the cross section of the wire must not be less than 0.4 mm2. The wiring in the wire box should take measures to prevent the end of the wire from falling off the lamp. Lamps weighing more than 1 kg should be equipped with hanging chains. When the chandelier lamps weigh more than 3 kg, they should be fixed by embedded hooks or bolts. The light wire of the pendant chain lamp should not be subjected to tension, and the light wire should be woven together with the pendant chain.

    4. Ceiling lamps with incandescent lamps as light sources shall not be directly installed on combustible components; bulbs shall not be close to the lampshade; when the distance between the bulb and the insulating table is less than 5 mm, heat insulation measures should be taken between the bulb and the insulating table . The power of the incandescent lamp must not exceed the maximum power allowed by the lamp.

    5. When the fluorescent lamp is used as the light source, the ballast should be installed on the phase line, and there should be a shell on the lamp to prevent the lamp feet from falling off, and there should be a margin in the lamp box. The frame of the giant lamp is parallel to the decorative line of the ceiling. The frame should be close to the ceiling surface.

    6. The phase line of the screw lamp cap should be connected to the terminal of the center contact, the neutral line should be connected to the screw terminal, and the insulating shell of the lamp cap should be intact and free from damage and leakage.

    7. The diameter of the hook for fixing the lantern should not be smaller than the hook of the lamp, and the diameter of the lamp should not be less than 6 mm.

    The above content is organized and shared by LED Street Light Housing | Die-cast Aluminum Light Housing Manufacturer, hoping to help those in need.

    Aluminum Lamp Housing Manufacturer Introduces The Installation Skills Of Lamps Aluminum Lamp Housing Manufacturer introduces the installation requirements of common lamps 1. The lamps and accessories should be complete, and there should be no defects such as mechanical damage, deformation, peeling paint and cracked lampshades. 2. The bearing capacity of the fixture on the wall ceiling where the luminaire is installed should match the weight of the luminaire. 3. The chandelier should be equipped with a wire box, and each wire box can only be equipped with one set of chandelier. The surface of the chandelier must be well insulated, there must be no joints, and the cross section of the wire must not be less than 0.4 mm2. The wiring in the wire box should take measures to prevent the end of the wire from falling off the lamp. Lamps weighing more than 1 kg should be equipped with hanging chains. When the chandelier lamps weigh more than 3 kg, they should be fixed by embedded hooks or bolts. The light wire of the pendant chain lamp should not be subjected to tension, and the light wire should be woven together with the pendant chain. 4. Ceiling lamps with incandescent lamps as light sources shall not be directly installed on combustible components; bulbs shall not be close to the lampshade; when the distance between the bulb and the insulating table is less than 5 mm, heat insulation measures should be taken between the bulb and the insulating table . The power of the incandescent lamp must not exceed the maximum power allowed by the lamp. 5. When the fluorescent lamp is used as the light source, the ballast should be installed on the phase line, and there should be a shell on the lamp to prevent the lamp feet from falling off, and there should be a margin in the lamp box. The frame of the giant lamp is parallel to the decorative line of the ceiling. The frame should be close to the ceiling surface. 6. The phase line of the screw lamp cap should be connected to the terminal of the center contact, the neutral line should be connected to the screw terminal, and the insulating shell of the lamp cap should be intact and free from damage and leakage. 7. The diameter of the hook for fixing the lantern should not be smaller than the hook of the lamp, and the diameter of the lamp should not be less than 6 mm. The above content is organized and shared by LED Street Light Housing | Die-cast Aluminum Light Housing Manufacturer, hoping to help those in need.
    0 Comments 0 Shares
  • Aluminum Lamp Housing Manufacturer Introduces The Role Of Led Street Light Poles


    Aluminum Lamp Housing manufacturer introduces the function and design process of LED street light poles


    The function of LED street light pole:
    LED street lights are an important part of public facilities, and they can be seen everywhere in our lives. LED street lights can provide us with lighting at night. The quality of the light poles is very important because the light poles are installed outdoors and must pass through the wind. Blowing in the sun, if the lamp pole is not installed properly, it will directly cause the overload operation of the LED lighting street lamp. It may even bring security risks. In order to avoid such a situation, we must require outdoor LED street light poles to be reasonable and reasonable when designing.

    The craft of LED street light pole:
    In terms of the design of the street light pole, you can definitely know that when choosing a light pole, you should choose a light pole with a better material, so you don't have to worry about the damage of the light pole due to material problems. Generally, street light poles are made of Q235 steel. After the overall hot-dip galvanizing and high-temperature electrostatic spraying, it can be guaranteed for 15 years without rust. The cable for installing street light poles must be long and the joints need to be reasonably designed. Only these are guaranteed Then, we can guarantee that there will be no problems when the LED street lights are working.


    The above content is organized and shared by LED Street Light Housing | Die-cast Aluminum Light Housing manufacturer, hoping to help those in need.

    Aluminum Lamp Housing Manufacturer Introduces The Role Of Led Street Light Poles Aluminum Lamp Housing manufacturer introduces the function and design process of LED street light poles The function of LED street light pole: LED street lights are an important part of public facilities, and they can be seen everywhere in our lives. LED street lights can provide us with lighting at night. The quality of the light poles is very important because the light poles are installed outdoors and must pass through the wind. Blowing in the sun, if the lamp pole is not installed properly, it will directly cause the overload operation of the LED lighting street lamp. It may even bring security risks. In order to avoid such a situation, we must require outdoor LED street light poles to be reasonable and reasonable when designing. The craft of LED street light pole: In terms of the design of the street light pole, you can definitely know that when choosing a light pole, you should choose a light pole with a better material, so you don't have to worry about the damage of the light pole due to material problems. Generally, street light poles are made of Q235 steel. After the overall hot-dip galvanizing and high-temperature electrostatic spraying, it can be guaranteed for 15 years without rust. The cable for installing street light poles must be long and the joints need to be reasonably designed. Only these are guaranteed Then, we can guarantee that there will be no problems when the LED street lights are working. The above content is organized and shared by LED Street Light Housing | Die-cast Aluminum Light Housing manufacturer, hoping to help those in need.
    0 Comments 0 Shares
  • Aluminum Lamp Housing Manufacturer Introduces The Cause Of Led Heat

    As a new generation of lighting technology, LED technology has been widely used. At present, most lighting places use LED lamps. LED lamps and lanterns applications include square floodlight housings, LED wall washers, LED tunnel lights, etc., which are all used in various lighting places. . In the process, the power of LED lamps is gradually increased to meet the lighting needs, and the power of LED lamps is gradually increased. Therefore, the heat dissipation problem of LED lamps has attracted more and more attention. This is because the light decay of the LED or its life is directly related to its junction temperature. If the heat dissipation is not good, the junction temperature will be high and the life will be short. The Aluminum Lamp Housing manufacturer will show you the cause of the heat of the LED.

    The reason why LEDs generate heat is that not all the added electric energy is converted into light energy, but a part of the electric energy is converted into heat energy. At present, the light efficiency of LED is only 100lm/W, and its electro-optical conversion efficiency is only about 20-30%. In other words, approximately 70% of electrical energy is converted into heat.


    The above content is organized and shared by LED Street Light Housing | Die-cast Aluminum Light Housing manufacturer, hoping to help those in need.



    Aluminum Lamp Housing Manufacturer Introduces The Cause Of Led Heat As a new generation of lighting technology, LED technology has been widely used. At present, most lighting places use LED lamps. LED lamps and lanterns applications include square floodlight housings, LED wall washers, LED tunnel lights, etc., which are all used in various lighting places. . In the process, the power of LED lamps is gradually increased to meet the lighting needs, and the power of LED lamps is gradually increased. Therefore, the heat dissipation problem of LED lamps has attracted more and more attention. This is because the light decay of the LED or its life is directly related to its junction temperature. If the heat dissipation is not good, the junction temperature will be high and the life will be short. The Aluminum Lamp Housing manufacturer will show you the cause of the heat of the LED. The reason why LEDs generate heat is that not all the added electric energy is converted into light energy, but a part of the electric energy is converted into heat energy. At present, the light efficiency of LED is only 100lm/W, and its electro-optical conversion efficiency is only about 20-30%. In other words, approximately 70% of electrical energy is converted into heat. The above content is organized and shared by LED Street Light Housing | Die-cast Aluminum Light Housing manufacturer, hoping to help those in need.
    0 Comments 0 Shares
  • High Quality Street Light Housing Supplier Introduces Street Light Design Knowledge


    The High Quality Street Light Housing supplier introduced that the height of street lights is proportional to the width of the road:
    The relationship between the height of the street light pole and the road width is very large. Generally speaking, the height of the street light and the road width are proportional. For example, a 6-meter-wide road is generally equipped with a street light pole with a height of about 6 meters, and an 8-meter-wide road is generally configured with 8 Light poles with a height of about meters.

    The supplier of High Quality Street Light Housing introduced that the height of the street light is related to the width of the road and the light source:
    The height of the street lamp and the width of the street are also related to the size of the light source. The higher the height of the pole, the greater the power of the light source, the lower the height of the pole, the lower the power of the light source, and the width of the street lamp can also be smaller. Customers must be sure to purchase Communicate your requirements and environment with customer service clearly, so that it will neither cause waste of resources nor affect the lighting of street lights.

    The above content is compiled and shared by the LED Street Light Housing | Die-cast Aluminum Light Housing manufacturers , hoping to help those in need.

    High Quality Street Light Housing Supplier Introduces Street Light Design Knowledge The High Quality Street Light Housing supplier introduced that the height of street lights is proportional to the width of the road: The relationship between the height of the street light pole and the road width is very large. Generally speaking, the height of the street light and the road width are proportional. For example, a 6-meter-wide road is generally equipped with a street light pole with a height of about 6 meters, and an 8-meter-wide road is generally configured with 8 Light poles with a height of about meters. The supplier of High Quality Street Light Housing introduced that the height of the street light is related to the width of the road and the light source: The height of the street lamp and the width of the street are also related to the size of the light source. The higher the height of the pole, the greater the power of the light source, the lower the height of the pole, the lower the power of the light source, and the width of the street lamp can also be smaller. Customers must be sure to purchase Communicate your requirements and environment with customer service clearly, so that it will neither cause waste of resources nor affect the lighting of street lights. The above content is compiled and shared by the LED Street Light Housing | Die-cast Aluminum Light Housing manufacturers , hoping to help those in need.
    0 Comments 0 Shares
  • 150w Street Light Housing Shares Street Light Design Techniques

    150w Street Light Housing manufacturer shares LED street lighting design:

    Traditional LED street lamp design mainly focuses on the number of lumens of the LED, while less attention is paid to heat dissipation. In fact, the lumens of LEDs are increasing rapidly.

    The number of lumens per watt of LED has reached 100 lumens, and this value is still growing rapidly. The corresponding heat transfer theory system has been mature, and the heat transfer methods we can use are basically clear: conduction, convection, radiation and phase change heat transfer. Therefore, in terms of heat transfer or heat dissipation, the measures we can take are visible and limited.

    The above content is compiled and shared by LED Street Light Housing | Die-cast Aluminum Light Housing manufacturers, hoping to help those in need.

    150w Street Light Housing Shares Street Light Design Techniques 150w Street Light Housing manufacturer shares LED street lighting design: Traditional LED street lamp design mainly focuses on the number of lumens of the LED, while less attention is paid to heat dissipation. In fact, the lumens of LEDs are increasing rapidly. The number of lumens per watt of LED has reached 100 lumens, and this value is still growing rapidly. The corresponding heat transfer theory system has been mature, and the heat transfer methods we can use are basically clear: conduction, convection, radiation and phase change heat transfer. Therefore, in terms of heat transfer or heat dissipation, the measures we can take are visible and limited. The above content is compiled and shared by LED Street Light Housing | Die-cast Aluminum Light Housing manufacturers, hoping to help those in need.
    0 Comments 0 Shares
  • Aluminum Lamp Housing Has A Long Life
    Product features of Aluminum Lamp Housing :

    1. High efficiency and energy saving At the same brightness, LED energy-saving lamps consume only 1 kWh in 1000 hours, ordinary incandescent lamps consume 1 kWh in 17 hours, and ordinary energy-saving lamps consume 1 kWh in 100 hours;

    2. The theoretical service life of the ultra-long service life can reach more than 100,000 hours, the service life of ordinary energy-saving lamps is 6,000 hours, and the service life of ordinary incandescent lamps is 1,000 hours.

    3. Healthy light The light does not contain ultraviolet rays and infrared rays, and there is no radiation. The ordinary energy-saving lamps and incandescent lamps contain ultraviolet rays and infrared rays;

    4. Green and environmental protection, free of harmful elements such as mercury and lead, which is beneficial to recycling and will not produce electromagnetic interference. Ordinary lamps contain harmful elements such as mercury and lead, and electronic ballasts in energy-saving lamps will produce electromagnetic interference;

    5. Protection of eyesight DC drive, no stroboscopic, ordinary lights are AC driven, it will inevitably produce stroboscopic;

    6. High light efficiency, low heat generation, 90% of the electric energy is converted into visible light, 80% of the electric energy of ordinary incandescent lamps is converted into thermal energy, and only 20% of the electric energy is converted into visible light;

    7. High safety factor The required voltage and current are small, there is little heat, there is no hidden danger, and it can be used in dangerous places such as mines;


    The above content is organized and shared by LED Street Light Housing | Die-cast Aluminum Light Housing . Welcome to the station to learn more.
    Aluminum Lamp Housing Has A Long Life Product features of Aluminum Lamp Housing : 1. High efficiency and energy saving At the same brightness, LED energy-saving lamps consume only 1 kWh in 1000 hours, ordinary incandescent lamps consume 1 kWh in 17 hours, and ordinary energy-saving lamps consume 1 kWh in 100 hours; 2. The theoretical service life of the ultra-long service life can reach more than 100,000 hours, the service life of ordinary energy-saving lamps is 6,000 hours, and the service life of ordinary incandescent lamps is 1,000 hours. 3. Healthy light The light does not contain ultraviolet rays and infrared rays, and there is no radiation. The ordinary energy-saving lamps and incandescent lamps contain ultraviolet rays and infrared rays; 4. Green and environmental protection, free of harmful elements such as mercury and lead, which is beneficial to recycling and will not produce electromagnetic interference. Ordinary lamps contain harmful elements such as mercury and lead, and electronic ballasts in energy-saving lamps will produce electromagnetic interference; 5. Protection of eyesight DC drive, no stroboscopic, ordinary lights are AC driven, it will inevitably produce stroboscopic; 6. High light efficiency, low heat generation, 90% of the electric energy is converted into visible light, 80% of the electric energy of ordinary incandescent lamps is converted into thermal energy, and only 20% of the electric energy is converted into visible light; 7. High safety factor The required voltage and current are small, there is little heat, there is no hidden danger, and it can be used in dangerous places such as mines; The above content is organized and shared by LED Street Light Housing | Die-cast Aluminum Light Housing . Welcome to the station to learn more.
    0 Comments 0 Shares
  • 100w Street Light Housing Manufacturers Share The Height Design Of Street Lights

    100w Street Light Housing manufacturer introduces street lamp height and spacing:

    The height and spacing of street lamps are proportional: the relationship between the height and spacing of street lamps is very large. Generally speaking, the height and spacing of street lamps are proportional to each other. It is about -20 meters, and 8 meters wide roads are generally equipped with light poles about 8 meters high, and the distance between street lights is about 20-25 meters.

    The height and spacing of street lamps are also related to the light source: the height and spacing of street lamps are also related to the size of the light source. The higher the height of the pole light source power is, the larger the spacing can be. The lower the height of the pole light source power is, The street lamp spacing can also be small. Customers must communicate their requirements and environment with customer service clearly when purchasing, so that it will not cause waste of resources nor affect the lighting of street lamps.

    To learn more, please check here LED Street Light Housing | Die-cast Aluminum Light Housing .
    100w Street Light Housing Manufacturers Share The Height Design Of Street Lights 100w Street Light Housing manufacturer introduces street lamp height and spacing: The height and spacing of street lamps are proportional: the relationship between the height and spacing of street lamps is very large. Generally speaking, the height and spacing of street lamps are proportional to each other. It is about -20 meters, and 8 meters wide roads are generally equipped with light poles about 8 meters high, and the distance between street lights is about 20-25 meters. The height and spacing of street lamps are also related to the light source: the height and spacing of street lamps are also related to the size of the light source. The higher the height of the pole light source power is, the larger the spacing can be. The lower the height of the pole light source power is, The street lamp spacing can also be small. Customers must communicate their requirements and environment with customer service clearly when purchasing, so that it will not cause waste of resources nor affect the lighting of street lamps. To learn more, please check here LED Street Light Housing | Die-cast Aluminum Light Housing .
    0 Comments 0 Shares
  • 100w Street Light Housing Wholesaler Shares The Selection Of Lamps
    Lamps are used in every home decoration. Good lamps can not only play the role of lighting, but also play the role of decoration, so many people pay more attention to the purchase of lamps, then 100w Street Light Housing Wholesaler will teach What are your lighting purchase skills? First of all, the style of lamps should be selected according to their actual needs and personal preferences. For...
    0 Comments 0 Shares
  • 100w Street Light Housing Wholesale Shares The Characteristics Of Led High Bay Light Housing



    100w Street Light Housing Wholesale Shares The Use Environment Of Led High Bay Lamp Housing

    100w Street Light Housing Wholesale shares the main performance characteristics of LED high bay lamp housing:

    1. Create a safe operating environment

    (1) LED light source to ensure instant cold start and hot start of lamps;

    (2) The structure of the integrated aluminum alloy profile is simple and convenient, and has good impact resistance, and can be reliably operated in a stable environment under vibration and shock;

    (3) Excellent light distribution planning and anti-glare planning, which can effectively prevent the visual fatigue of operators.


    2. Easily complete energy saving goals

    (1) High-power LED high bay light source, accurate light distribution plan, cooperation 99.99% high-purity aluminum reflector cup and imported PC bright parts with light transmittance up to 93%, lamp power up to 79%, higher than professional level 40 %the above;

    (2) Advanced and reasonable circuit planning, excellent cooperation components, electrical power up to 90%, more than 6% higher than occupation.


    3. Reduce the amount of protection work

    (1) There is no need to replace the light source for 7 consecutive years of uninterrupted operation, and the life span is nearly 10 times that of fluorescent lamps;

    (2) The shell's anti-corrosion grade WF2, to ensure that the lamps are not corroded or rusted in harsh environments;

    (3) The protection grade can reach IP65;

    (4) According to the national military standard quality control system, through the strict reliability and aging test, the lamp failure rate is lower;

    (5) The groove design is adopted on the reverse side of the LED lamps to increase the heat dissipation area and extend the service life.

    The above content is organized and shared by Hot-Selling Street Light Housing Wholesale, hoping to help those in need.
    100w Street Light Housing Wholesale Shares The Characteristics Of Led High Bay Light Housing 100w Street Light Housing Wholesale Shares The Use Environment Of Led High Bay Lamp Housing 100w Street Light Housing Wholesale shares the main performance characteristics of LED high bay lamp housing: 1. Create a safe operating environment (1) LED light source to ensure instant cold start and hot start of lamps; (2) The structure of the integrated aluminum alloy profile is simple and convenient, and has good impact resistance, and can be reliably operated in a stable environment under vibration and shock; (3) Excellent light distribution planning and anti-glare planning, which can effectively prevent the visual fatigue of operators. 2. Easily complete energy saving goals (1) High-power LED high bay light source, accurate light distribution plan, cooperation 99.99% high-purity aluminum reflector cup and imported PC bright parts with light transmittance up to 93%, lamp power up to 79%, higher than professional level 40 %the above; (2) Advanced and reasonable circuit planning, excellent cooperation components, electrical power up to 90%, more than 6% higher than occupation. 3. Reduce the amount of protection work (1) There is no need to replace the light source for 7 consecutive years of uninterrupted operation, and the life span is nearly 10 times that of fluorescent lamps; (2) The shell's anti-corrosion grade WF2, to ensure that the lamps are not corroded or rusted in harsh environments; (3) The protection grade can reach IP65; (4) According to the national military standard quality control system, through the strict reliability and aging test, the lamp failure rate is lower; (5) The groove design is adopted on the reverse side of the LED lamps to increase the heat dissipation area and extend the service life. The above content is organized and shared by Hot-Selling Street Light Housing Wholesale, hoping to help those in need.
    0 Comments 0 Shares
More Stories

How to Use Phonetic Keyboard - See example below

Use combinations of english letter constants and vowels to form the amharic pronounciation. Note the use of upper case E and W to write "ሜ" and "ሟ", respectively. Press Esc to toggle writing between English and Amharic Keyboard. See the example table below to form the "መ" variations.

 euiaE oW
m

How to Use Amharic BHN Keyboard - See example below

When you click one of the root characters, all the variations will show up on the keyboard. You can then type the variation you want.